Used, DMG Mori i 30 V CNC Vertical Machining Center
Brand
DMG MORI
Model
I 30V-SN
Type
Machining Centers, Vertical
Stock #
20182
Condition
Used
Year
2019
Location
City Not Specified,
Specifications
| Taper | CAT 40 DUAL CONTACT |
| X Axis Travel | 15.7 inches |
| Y-Axis Travel | 10.6 inches |
| Z Axis Travel | 11 inches |
| Max Spindle Speed (RPM) | 12000 |
| Spindle Motor | 7.5 horsepower |
| Table-L | 11.8 inches |
| Table-W | 23.6 inches |
| Max Table Load | 330 pounds |
| CNC Control | yes |
| Type of CNC Control | DMG Mitsubishi Electric M730UM |
| Tool Changer Capacity | 14 |
| Rapid Traverse Rate (X/Y/Z) | 2,440 (ipm) |
| Tool Change Time | 3 Seconds |
| Dimensions | 61.3W x 128.9D x 104.3H |
| Weight | 10846 pounds |
Equipped With
Distance from table surface to spindle gauge plane: 9.4 - 20.5"
Max Tool Length: 10"
Max Tool Weight: 14 lb.
Max Feed Rate: 2,440 ipm
Number of Pallets: 2
Method of Pallet Change: Rotation
Pallet Change Time: 2 seconds
FACTORY OPTIONS INCLUDED: COST: $135,000 over base machine
Standard spindle 12,000 min-1, 5.5/ 3.7 kW (#40)
Max Tool Length: 10"
Max Tool Weight: 14 lb.
Max Feed Rate: 2,440 ipm
Number of Pallets: 2
Method of Pallet Change: Rotation
Pallet Change Time: 2 seconds
FACTORY OPTIONS INCLUDED: COST: $135,000 over base machine
Standard spindle 12,000 min-1, 5.5/ 3.7 kW (#40)
Spindle Taper 7/24 Taper #40 (two-face contact)/ Grip CAT
Preparation for Center Through-spindle coolant system
Retention Knob: Special (Center-Through) (7/24 Taper #40)
Changing to Tapped pallets (2 pallets)
Interface for Hydraulic fixture (2 circuits x 2, 4 ports on each pallet)
Interface for Workpiece seating detection (2 lines x 2, 2 ports on each pallet)
Tool magazine door
Usable Coolant Type: Water-Soluble Coolant
Chip conveyor (rear discharge, magnet scraper type)
Interface for Through-Spindle Coolant System (7 MPa, Constant Pressure)
Coolant gun
Fixture washing coolant
Shower coolant
Mist collector (AFS 600), including stand (SK-OP)
Oil Skimmer (Belt type) (SK-OP)
Signal lamp 4 colors (Red, yellow, green, blue)
Automatic door (No Tape switch)
Interface for EtherNet/IP (SK-OP)
Interface for Robot (EtherNet/IP), Need to select EtherNet/IP Interface
Interface for Gage (EtherNet/IP), Need to select EtherNet/IP Interface (SK-OP)
High acceleration (including Dry anchor)
Spindle Head Cover
10 external M-codes (SK-OP)
Setting Unit inch
Multiple M codes in single block (Multi M code function)
Screen display English
MCC TMS
MAPPS Tool management system + Tool ID (MAPPS software only)
Tool ID system (Stand installed in MG)
Tool brackage detection(KEYENCE sensor PX-10CP)
Assembly fee for special option
DMQP: ChipBlaster M30/70 Unit - 8 gpm @ 1000 PSI 50 gal tank / cyclone filter (installed)
DMQP: ChipBlaster Sludge Settling Tank "Baffled settling tank for dirty coolant discharge: 35 gal capacity **recommended with all cyclonic filters (installed)
*All specifications are subject to verification
*All specifications are subject to verification